Общие свойства показателя скоростной чувствительности диаграмм деформирования, порождаемых линейной теорией вязкоупругости, и существование максимума у его зависимости от скоростистатья
Статья опубликована в журнале из списка RSCI Web of Science
Информация о цитировании статьи получена из
Scopus
Статья опубликована в журнале из перечня ВАК
Статья опубликована в журнале из списка Web of Science и/или Scopus
Дата последнего поиска статьи во внешних источниках: 8 апреля 2022 г.
Аннотация:В работе анализируется скоростная чувствительность семейства диаграмм деформирования, порождаемых физически линейным определяющим соотношением вязкоупругости Больцмана-Вольтерры с произвольной функцией релаксации в одноосных испытаниях с постоянными скоростями деформации. Выведено общее выражение для показателя скоростной чувствительности (скоростного упрочнения) и аналитически исследованы его общие качественные свойства: его зависимость от деформации, скорости деформации и характеристик функции релаксации, диапазон значений, интервалы монотонности и существование точек экстремума, предельные значения при стремлении скорости деформации к нулю или бесконечности, способы определения по диаграммам деформирования или по кривым релаксации. Установлено, что (в рамках линейной теории вязкоупругости) этот показатель зависит не от двух независимых аргументов (деформации и скорости деформации), а только от их отношения, что он выражается через отношение касательного модуля к секущему и может быть вычислен по одной диаграмме деформирования с произвольной скоростью деформации, и что по заданной (или измеренной в испытаниях) функции скоростной чувствительности можно однозначно восстановить функцию релаксации. Доказано, что значения показателя скоростной чувствительности всегда лежат в интервале от нуля до единицы (т.е. линейное ОС описывает только псевдопластические среды и не может описывать дилатантные) и могут быть сколь угодно близки к единице (верхней границе для псевдопластических сред), что как функция скорости он не только может монотонно возрастать или убывать, но может иметь точки экстремума, в частности, точку максимума (при мало обременительных ограничениях на функцию релаксации). Тем самым обнаружена неожиданная способность линейной теории вязкоупругости не только порождать семейство диаграмм деформирования с выраженными участками течения при практически постоянном напряжении, но и качественно описывать описывать «сигмоидальную» форму зависимости напряжения от скорости деформации (в логарифмических осях) и очень высокую скоростную чувствительность, характерные для режима сверхпластического деформирования материалов. Установленные свойства показателя скоростной чувствительности и его характерные особенности проиллюстрированы на примерах классических регулярных, сингулярных и фрактальных моделей вязкоупругости (Максвелла, Фойгта, Кельвина, Зенера, Бюргерса, Скотт-Блэра) и их параллельных соединений. *** А.V. Khokhlov. Properties of the strain rate sensitivity function produced by the linear viscoelasticity theory and existence of its maximum with respect to strain and strain rate * Strain rate sensitivity of stress-strain curves family generated by the Boltzmann-Volterra linear viscoelasticity constitutive equation (with an arbitrary relaxation modulus) under uni-axial loadings at constant strain rates is studied analytically as the function of strain and strain rate. The general expression for strain rate sensitivity index is derived and analyzed assuming relaxation modulus is arbitrary. Dependence of the strain rate sensitivity index on strain and strain rate and on relaxation modulus qualitative characteristics is examined, conditions for its monotonicity and for existence of extrema, the lower and the upper bounds and the limit values of the strain rate sensitivity as strain rate tends to zero or to infinity are studied. It is found out that (within the framework of the linear viscoelasticity) the strain rate sensitivity index which is, generally speaking, the function of two independent variables (namely strain and strain rate), depends on the single argument only that is the ratio of strain to strain rate. So defined function of one real variable is termed the strain rate sensitivity function and it may be regarded as a material function. The explicit integral expression (and the two-sided bound) for relaxation modulus in terms of strain rate sensitivity function is derived which enables one to restore relaxation modulus assuming a strain rate sensitivity function is given. The strain rate sensitivity function is represented as a linear function of ratio of tangent modulus to secant modulus of a stress-strain curve at any fixed constant strain rate and can be evaluated in such a way using test data. It is proved that the strain rate sensitivity value is confined in the interval from zero to unity (the upper bound of strain rate sensitivity index for pseudoplastic media) whatever strain and strain rate magnitudes are. It is found out that that the linear theory can reproduce increasing or decreasing or non-monotone dependences of strain rate sensitivity on strain rate (for any fixed strain) and it can provide existence of local maximum or minimum or several extrema as well without any complex restrictions on the relaxation modulus. General properties and peculiarities of the theoretic strain rate sensitivity function are illustrated by the examination of the classical regular and singular rheological models (consisting of two, three or four spring and dashpot elements) and fractional models. Namely, the Maxwell, Kelvin−Voigt, standard linear solid, Zener, anti-Zener, Burgers, anti-Burgers, Scott–Blair, fractional Kelvin−Voigt models and their parallel connections are considered. The analysis carried out let us to conclude that the linear viscoelasticity theory (supplied with common relaxation function which are non-exotic from any point of view) is able to produce high values of strain rate sensitivity index close to unity (the upper bound of strain rate sensitivity index for pseudoplastic media) and to provide existence of the strain rate sensitivity index maximum with respect to strain rate. Thus, it is able to simulate qualitatively existence of a flexure point on log-log graph of stress dependence on strain rate and its sigmoid shape which is one of the most distinctive features of superplastic deformation regime observed in numerous materials tests. Keywords: viscoelasticity, stress-strain curves at constant strain rates, strain hardening, strain rate sensitivity index (function), pseudoplastic media, fractional models, fractional differential equations, superplasticity, sigmoid curve, titanium and aluminum alloys, ceramics